SBIR and STTR topics › DoW/USAF
USAF
Pre-release
SBIRITARCMMC Level 2 (Self)
Wide Pass Bandwidth, High Selectivity, Continuously Tunable Notch Filters
Topic # DAF27BZ02-DV025 · DoW SBIR 2027 BAA · DoW/USAF · released 2026-11-04
Opens
Dec 2, 2026
Opens in 14 dayscloses Jan 6, 2027
DSIP topics appsearch DAF27BZ02-DV025 there
SBIR.gov page
Email me topics like this
Requirements to bid
CMMC Level 2 (Self)
Protection of Controlled Unclassified Information: the 110 requirements of NIST SP 800-171 Rev. 2. "Self" means you assess yourself every three years; "C3PAO" means an accredited third-party assessor certifies you every three years. Both need a yearly affirmation.
ITAR The work is export-controlled, which restricts who may work on it
(foreign nationals need authorisation).
A summary, not advice: the solicitation and 32 CFR Part 170 govern.
TPOC: Michael Page <[email protected]>; Michael Newberger <[email protected]>
Keywords: Tunable Filter; Notch Filter
Technology areas: Battlespace, Electronics, Sensors
Objective
Wideband receivers used in electronic warfare (EW), signals intelligence (SigInt), and electronic support measures (ESM) need to instantaneously capture broad swaths of spectrum to avoid missing frequency agile radio frequency (RF) signals. Wideband receivers, however, lack the dynamic range to capture wide bandwidths of spectrum containing both large interferers and weak signals of interest. Thus, multiple receivers are needed in these applications which results in large size and power consumption.
Description
The objective of this topic is to develop miniature, low power, and high selectivity tunable notch filters capable of protecting wideband receivers from large interferers. The effort will target the largest interferers which are in L, S, C, and X bands with tunable notch filters, while allowing pass bandwidths spanning L through Ku bands. Each notch filter must be continuously tunable across a minimum of 3 of the 4 targeted bands (L, S, C, and X) while having a notch depth > 20 dB and a notch bandwidth < 1 % across all tuned frequencies. With a narrow notch bandwidth, each notch filter must be programmable and maintained with an accuracy of 50% of the notch bandwidth and should maintain this accuracy over temperature. The notch filters must be able to reject large interfering signals and therefore should be able to notch receive interference levels greater than 5 dBm. In the bandpass each filter must cover L-Ku band (1-18 GHz) while maintaining a low insertion loss and noise figure of less than 1.5 dB and low passband distortion with an IIP3 > +50 dBm. Each notch filter must be small, less than 3 cc, and should be connectable in series without interfering with one another to notch multiple frequencies in the same receive chain. Finally, the power consumption, including any tuning electronics, of each notch filter should be less than 100 mW. The required metrics are:
Passband frequency range (GHz)1 – 18
Maximum passband insertion loss or noise figure (dB) ≤ 1.5
Passband IIP3 (dBm)≥ 50
Notch band tunable frequency range (GHz)1 – 12
Number of bands covered by a single, continuously tunable notch≥ 3
Minimum notch depth across all tuned notch states (dB)≥ 20
Maximum notch fractional bandwidth (%)≤ 1Size (cc)≤ 3
Power consumption (mW)≤ 100
Phase I
This topic is intended for a technology proven ready to move directly into a Phase II program. A Phase I SBIR award will not be made. The offeror is required to provide details and documentation in the Direct to Phase II (D2P2) proposal which demonstrates accomplishments of a "Phase I-like" effort, including demonstrating the expertise needed to design and fabricate miniature, high selectivity tunable notch filters. The offeror should have demonstrated, in a laboratory environment (TRL3), a notch filter achieving a 20dB deep notch with a bandwidth less than 5% of the tuned frequency, a continuous tuning range of at least 3:1, and a passband insertion loss below 3 dB across a wide frequency range. Demonstration of zero static power tuning and a filter volume of approximately 1 cc is desired. The offeror should have demonstrated the capability of maintaining low passband distortion and high notch depth across all tuned states. The proposal should illustrate past success at the aforementioned performance levels with tunable notch filter technologies fitting the above descriptions
Phase II
The desired outcome of this topic is to demonstrate miniature, low power, and high selectivity tunable notch filters capable of protecting wideband receivers from large interferers. The effort will deliver prototype notch filters continuously tunable across a minimum of 3 of the 4 targeted bands (L, S, C, and X) while having a notch depth > 20 dB and a notch bandwidth < 1 % across all tuned frequencies.
Phase III / dual use
Phase III is accomplished when the DoW and/or commercial applications of this SBIR-funded R&D are developed using non-SBIR/STTR funds. The most direct military application is the integration of these miniature, continuously tunable notch filters into the RF front ends of wideband receivers used for electronic warfare (EW), signals intelligence (SigInt), and electronic support measures (ESM). By selectively rejecting large interferers and jammers in L, S, C, and X bands while preserving reception across the full L–Ku passband, the filters enable a single high-dynamic-range wideband receiver to replace multiple narrowband receivers, directly reducing platform size, weight, and power. Additional DAF and DoW transition opportunities include receiver protection in airborne and ground-based radar systems, jam-hardened wideband communications and SATCOM-on-the-move terminals, and reconfigurable RF front ends for software-defined radios, where the same look-through capability allows the system to respond to threat pulses without missing frequency-hopped waveforms. Potential commercial applications include interference mitigation for 5G systems operating adjacent to incumbent services (such as C-band interference into radio altimeters and co-channel interference in cellular receivers), test and measurement instrumentation, and spectrum-monitoring equipment, all markets where compact, low-power, high-selectivity tunable filtering is increasingly required as the spectrum becomes more congested. The expected Phase III effort would advance the technology from its Phase II exit point of TRL5 toward TRL7 and beyond through integration into a host receiver subsystem, environmental qualification to applicable military standards, and demonstration in a relevant operational environment. This effort would also include maturation of the manufacturing process to support production quantities, screening and reliability testing, and the establishment of a qualified supply chain. Transition planning anticipates partnership with a DoW prime contractor or system integrator as the host platform sponsor, with the small business supplying the notch filter as a component or subassembly. Known government activities required prior to fielding include security classification review, ITAR/export-control determination, and any platform-specific airworthiness or system certification associated with the selected transition host. Early engagement with DAF program offices, EW and SigInt system developers, and additional DoW customers during Phase II is recommended to identify a committed transition partner and to align the filter's form factor and interface with the targeted receiver architecture.
References
- J. Roessler, E. Lever, A. Egbert, C. Baylis, R. Marks, B. Kirk, and A. Bouvy, "Overview of Tunable Notch Filters for Radar Systems," 2024. doi: available via IEEE Xplore (document 10619014).
- F. Lin and M. Rais-Zadeh, "Tunable RF MEMS Filters: A Review," in Encyclopedia of Nanotechnology, B. Bhushan, Ed. Dordrecht: Springer, 2015. doi: 10.1007/978-94-007-6178-0_100959-1
- Reines, S.-J. Park, I. El-Tanani, A. Grichener, and G. M. Rebeiz, "Compact Low-Loss Tunable X-Band Bandstop Filter With Miniature RF-MEMS Switches, "IEEE Transactions on Microwave Theory and Techniques, vol. 58, no. 7, pp. 1887–1895, Jul. 2010.
- M. Fernández-Bolaños, C. Dehollain, P. Nicole, and A. M. Ionescu, "Tunable band-stop filter based on single RF MEMS capacitive shunt switch with meander arm inductance, "Solid-State Electronics, vol. 54, no. 9, pp. 1033–1040, 2010. doi: 10.1016/j.sse.2010.04.030.
- L. Wang, T. Du, et al., "High-selectivity wideband bandpass filter with tunable notched band,"AEU – International Journal of Electronics and Communications, 2025.
- D. Mardivirin, F. Barrière, A. Pothier, A. Crunteanu, and P. Blondy, "A 2 Pole 9.6–11.7 GHz Band Stop Filter Using Analog Tuning RF MEMS Varactors," inProc. 2011 European Microwave Integrated Circuits Conf. (EuMIC), Manchester, UK, Oct. 2011, pp. 530–533.
- Analog Devices, "How Digitally Tunable Filters Enable Wideband Receiver Applications, "Analog Dialogue. [Online]. Available: https://www.analog.com/en/resources/analog-dialogue/articles/how-digitally-tunable-filters-enable-wideband-receiver-applications.html
Copied from the official source and may be out of date. Confirm dates and requirements in the
official solicitation.